Butler Group Components Power Supplies AC-DC Power Supplies MS Series 30 kW to 75 kW

MS Series 30 kW to 75 kW

Datasheet

  • Features

    High Frequency IGBT-based Switch-Mode Design

    The MS Series utilizes the latest IGBT devices to drive down size and increase performance. The high frequency design delivers fast transient response and low output ripple. This performance coupled with Magna-Power's rugged current-fed power processing, enables confidence in even the most demanding applications.

    Fully Programmable Power

    All MS Series functions and features of are available and programmable from a variety of control methods, including:

    • Stepless front panel knobs
    • 37-pin isolated analog-digital I/O
    • Computer interface with software and drivers

    Various programming interfaces are available, such as LXI TCP/IP Ethernet (+LXI), IEEE-488 GPIB (+GPIB), Edgeport USB, Accessory (+USB), RS485 Accessory (+RS485).

    Broad Voltage-Current Range, Consistent Controls

    Magna-Power Electronics MS Series is built on the same power processing modules as the TS Series, only packaged in a floor-standing cabinet with casters and expanding into higher power levels. The available The MS Series models covers a very wide output range, spanning from voltage levels up to 4000 Vdc (floating) and current levels up to 4500 Adc. Models 30 kW to 60 kW are available in a 38.5” high cabinet, while 75 kW models are available in a 49” high chassis.

    Designed for Safety

    MS Series power supplies have extensive diagnostic functions, including: phase loss, excessive thermal conditions, over voltage trip (programmable), over current trip (programmable), cleared fuse, and excessive program line voltage. When in standby or diagnostic fault, the AC mains are mechanically disconnected via an embedded AC contactor, providing confidence that the unit is only processing power when desired.

    Scalable Master-Slave Operation

    For maximum flexibility, all MS Series power supplies can be scaled a in master-slave configuration for higher voltage or current output. Using the plug and play Universal Interface Device (+UID47), units are tied together in via their 37-pin I/O, allowing an increase in system current when configured in parallel or increase in system voltage when configured in series—up to the power supply's output isolation rating.

    Extensive Programming Support and Included Software

    All MS Series power supplies come standard with a National Instruments LabVIEW™ and LabWindows™/CVI drivers. In addition, an IVI driver is included supporting Visual C++, Visual C#, Visual Basic .NET, MATLAB, Measure Foundry, PAWS, Visual Basic 6.0, and Agilent VEE Pro. A Standard Commands for Programmable Instrumentation (SCPI) command set is also supported, allowing programming using raw ASCII commands. Finally, Magna-Power's RIS Panel software is provided allowing for a virtual control panel controlling the power supply via any of the available communication interfaces.

    Models

    There are hundreds of possible configurations for the MS Series product. Using the following ordering guide and models chart to define the best model for your application. Need less power? Visit our TS Series product line. Need more power? Visit our MT Series product line.

    Model Ordering Guide

    Diagrams

    For maximum flexibility, all front panel function and controls have equivalent programming and monitoring functions on the included rear 37-pin analog-digital I/O connector and on the computer programming interface.

    A Version Front Panel (MSA)

    The A Version front panel provides a digital display with rotary front panel input, isolated 37-pin analog-digital I/O, and a RS232 computer interface.

    D Version Front Panel (MSD)

    In addition to the features of the A Version front panel, the D Version front panel provides digital 10-key entry, auto-sequencing with memory capability, and modulation for non-linear power profile emulation.

    C Version Front Panel (MSC)

    The C Version front panel is blank, providing only a switch to enable control power. All control must be performed by the provided isolated 37-pin analog-digital I/O or through a computer interface.

    A
    • Engages and disengages main power
    B
    Meters display output voltage, output current, voltage set point, current set point, over voltage trip, and over current trip
    C
    Over voltage trip and over current trip setting potentiometers
    D
    Mode




    • POWER: Indicates power output
    • STANDBY: Indicates control power only
    E
    Configuration




    • REM SEN: Remote sense enabled
    • INT CTL: Front panel start/stop/clear enabled
    • EXT CTL: External start/stop/clear enabled
    • ROTARY: Front panel rotary knob input
    • KEYPAD: 10-digit numeric keypad control
    • EXT PGM: External analog voltage-current control
    • REMOTE: Computer control
    F
    Diagnostic Alarms




    • LOCK: Interlock
    • PGM LN: External input voltage beyond limits
    • OVT: Over voltage protection has tripped
    • OCT: Over current protection has tripped
    • THERM: Over temperature condition
    • PHASE: Under voltage AC input
    • FSE: Warns that a fuse has cleared
    • ARM: Indicates power supply is ready for or operating in auto-sequencing
    G
    Power switch energizes control circuits without engaging main power Diagnostic Alarms
    H
    Stepless rotary knob to set voltage-current
    I
    Function Keys




    • MENU: Selects function
    • ITEM: Selects item within function
    • V/I DIS: Displays voltage-current settings
    • TRIP DIS: Displays OVT and OCT setting
    • CLEAR: Clears settings or resets fault
    • ENTER: Select item
    J
    Memory location indicator, used for auto-sequencing applications
    K
    Digital input keypad

    Front Side Dimensions

    Rear Side Dimensions

    Front panel dimensions diagram references to "a" correspond to values in following table:

    Power a
    30 kW 27.00"
    45 kW 46.75"
    60 kW 46.75"
    75 kW 46.75"
    1
    Front Panel Controller
    2
    Air Exhaust Fans
    3
    Front Air Intake (Air Cooled Models Only)
    4
    DC Output Bus (See Details Below)
    5
    Connections for External Control
    6
    Input AC Connections (4-wire)
    Qty (4) 3-8/16 2” Studs
    7
    (4) Casters: (2) Locking, (2) Non-Locking

    Note: Additional diagrams available for download of MS Series units with Water Cooling +WC option.

    High Voltage Output Bus
    Models Above 1000 Vdc

    Medium Voltage Output Bus
    Models 80 Vdc to 1000 Vdc

    Low Voltage Output Bus
    Models below 80 Vdc

    Options

    The following options are available for the MS Series programmable DC power supply:




    CBL

    DC Power Cabling, Terminated

    Utilizing Magna-Power's internal cable manufacturing operations, custom-made DC power cables are offered as an accessory.

    More




    +ISO

    High Isolation Output
    Available for models rated for 250 Vdc to 1000 Vdc, the +ISO option extends the output isolation, used when the application demands floating or tying units in series beyond the standard 1000 Vdc output isolation rating.
    More




    +HS

    High Slew Rate Output
    The high slew rate option is a control modification and replaces the standard output stage with one of low capacitance film and/or aluminum electrolytic capacitors, capable of high RMS currents. This stage provides higher bandwidth with faster output rise and fall times.
    More




    +GPIB

    IEEE-488 GPIB Interface
    Full control of the product's features and diagnostics over a IEEE-488 GPIB interface. The GPIB interface allows up to 15 devices may be connected to one bus and is compatible with all Magna-Power provided software and drivers.
    More




    +BD

    Integrated Blocking Diode

    The Integrated Blocking Diode Option (+BD) provides an internally heat-sunk protection diode on the positive output terminal of a MagnaDC programmable DC power supply to protect the product's output from reverse voltage up to 1200 Vdc.

    More




    +LXI

    LXI TCP/IP Ethernet Interface
    Full control of all the product's features and diagnostics over a LXI Class C Certified TCP/IP Ethernet interface. Includes an embedded web server and compatibility with all Magna-Power provided software and drivers.
    More




    RS485

    RS-422 or RS-485 Converter (Accessory)

    The RS-232 to RS422 or RS-485 converter is an external industrial accessory to convert the power supply's standard RS-232. Unlike converters which require programming hardware handshaking signals to control RS-485 or RS-422 operation, the +RS485 option provides automatic control.

    More




    UID47

    Universal Interface Device (Accessory)

    The UID47 accessory eases master-slave parallel or series configuration of Magna-Power DC power supplies, enabling near equal current or voltage sharing, depending on the configuration. The accessory includes the UID47 with integrated circuitry and (2) 6-ft DB37 cables.

    More




    USB

    USB Edgeport Converter (Accessory)

    The +USB Edgeport Converter plugs directly into the product's RS232 port, creating a virtual serial COM port over USB. The converter is tested with the product by Magna-Power at time of production.

    More




    +WC

    Water Cooling
    Water cooling is available instead of the standard air cooling. Water cooled units are fully enclosed and to not take in any external air, making them ideal for corrosive environments, densely packed cabinets or setups where water is readily available.

    • Calibration Available
    • Training Available

    Contact us:

    Sales +353 1 629 2620

    Send Message
    LoadingUpdating...